- 您现在的位置：买卖IC网 > Sheet目录1193 > AC244005 (Microchip Technology)KIT MPLAB REAL ICE ISOLATOR
Installation
3.5
SETTING UP THE TARGET
Once the type of communication has been determined by inserting the corresponding
driver board into the emulator, the target must be set up to accommodate this, as well
as the type of target device to be used, i.e., regular or ICE.
Some devices have built-in debug circuitry. These “regular” devices may be used
directly by the emulator on the target.
Other devices have no built-in debug circuitry. For these devices, a special ICE device
( Device -ICE) is required, mounted on a header board. For more on header boards, see
the “ Header Board Specification “ (DS51292).
Note:
3.5.1
Some regular devices have ICE devices avaliable to provide dedicated
debug pins and (sometimes) memory.
Using Regular Devices
For regular devices, the emulator may be connected directly to the target board. The
device on the target board must have built-in debug circuitry in order for the MPLAB
REAL ICE in-circuit emulator to perform emulation with it. Consult the device data sheet
to see if the device has the needed debug circuitry, i.e., it should have a “Background
Debugger Enable” Configuration bit.
Note:
In the future, devices with circuitry that support ICD may be used, though
only standard debug, and not emulator debug, functions will be available.
The target board must have a connector to accommodate to the communications
3.5.2
Using ICE Devices and Header Boards
For ICE devices, an ICE header board is required. The header board contains the
hardware necessary to emulate a specific device or family of devices.
Note:
In the future, ICD header boards with ICD devices ( Device -ICD) may be
used, though only standard debug, and not emulator debug, functions will
be available.
A transition socket is used with the ICE header to connect the header to the target
board. Transition sockets are available in various styles to allow a common header to
be connected to one of the supported surface mount package styles. For more
information on transition sockets, see the “Transition Socket Specification” (DS51194).
Header board layout will be different for standard or high-speed communications. For
connection information, see Section 2.3.1 “Standard Communication” or
3.5.3
Powering the Target
If you have not already done so, connect the emulator pod to the target using the
Communications” ). Then power the target.
Note:
? 2008 Microchip Technology Inc.
The emulator cannot power the target.
DS51616B-page 29
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AC244006
KIT MPLAB REAL ICE TRACE
AC2626M6
PROBE TEMP 6" GENERAL PURP
AC300024
MOTOR STEPPER 2PHASE 8WIRE
AC300030
KIT ACOUSTIC ACCESSORY
ACM-16
CABLE MODULE FR3 16BIT 40-DIP
ACM-2X8
ACTIVE CABLE MODULE DUAL 8 BIT
ACM-8
CABLE MODULE FR3 8BIT 28/32-DIP
ACS9510EVB
EVALUATION BOARD FOR ACS9510
相关代理商/技术参数
AC244005-2
功能描述:处理器配件 MPLAB REAL ICE w/ Performace Pak RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
AC244006
功能描述:仿真器/模拟器 MPLAB REAL ICE TRACE INTERFACE Brd KIT RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
AC244007
制造商:Microchip Technology Inc 功能描述:MPLAB REAL ICE JTAG ADAPTER - Boxed Product (Development Kits) 制造商:Microchip Technology Inc 功能描述:ADAPTER MPLAB REAL ICE JTA 制造商:Microchip Technology Inc 功能描述:ADAPTER, MPLAB, REAL, ICE, JTAG 制造商:Microchip Technology Inc 功能描述:ADAPTER, MPLAB, REAL, ICE, JTAG; Accessory Type:JTAG adaptor Board; For Use With:Microchip PIC32MX devices; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes
AC244008
功能描述:处理器配件 MPLAB REAL ICE Power Monitor
RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
AC244022
功能描述:插座和适配器 Procs Extnsn Pak for PIC24FJ128GA010-ICE RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244022
制造商:Microchip Technology Inc 功能描述:Processor Extension Pak for PI
AC244023
功能描述:插座和适配器 PROCESSOR EXTNSN PAK FOR PIC18F1xK50 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244024
功能描述:插座和适配器 Processor Ext Pak for PIC18LF14K50 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x